Defining the Architecture

The architecture for this configuraiton is the SAM E70 Xplained Ultra + 4.3” WQVGA with SSD1963 GFX Interface Card interface through the 16-bit 8080 mode.

The SSD1963 is connected to the SAM E70 thru the SMC peripheral and GPIOs which are used to send 16-bit parallel data/commands and to bit-bang control signals to the SSD1963 controller, respectively. The frame buffer is stored externally in the SSD1963 controller.

User touch input on the display panel is received thru the PCAP capacitive touch controller, which sends a notification to the Touch Input Driver. The Touch Input Driver reads the touch information over I2C and sends the touch event to the Graphics Library thru the Input System Service.

Demonstration Features

Legato Graphics Library
Input system service and touch driver
Time system service, timer-counter peripheral library and driver
ILI9488 display 8-bit parallel mode driver (DMA-CCL boosted)
16-bit RGB565 color depth (8-bit palettized double buffering)
Port/GPIO peripheral
I2C peripheral library and driver
Images and Fonts for user interface stored in internal flas

Creating the Project Graph

Adding the SAM E54 Curiosity Ultra BSP and Legato Graphics w/ MXT Curiosity Pro Display Graphics Template component into the project graph.

This will automatically add the components needed for a graphics project and resolve their dependencies. It will also configure the pins needed to drive the external peripherals like the display and the touch controller.

For the DMA-CCL boosted setup, components TC4, CCL needs to be added.

Additional components to support File System, MSD Client Driver, USB Full Speed Driver, USB Host Layer, SDMMC, SDHC1, QSPI and SST26 needs to be added and connected manually.

Some of these components are fine with default settings, while other require some changes. The following is a list of all the components that required custom settings.

To setup the CCL to clock the pixel data, make sure PB09 is set to CCL_OUT2

Instead of write strobe, make sure PB17 is setup as RSDC instead

Building the Application

The parent directory for this application is gfx/apps/legato_adventure. To build this application, use MPLAB X IDE to open the gfx/apps/legato_adventure/firmware/legato_adv_e54_cu_cpro_parallel.X project file.

The following table lists configuration properties:

Project Name	BSP Used	Graphics Template Used	Description
legato_adv_e54_cu_cpro_parallel.X	SAM E54 Curiosity Ultra BSP	Legato Graphics w/ Xplained Pro Display	SAM E54 Curiosity Ultra w/ maXTouch Xplained Pro display via 8-bit parallel interface

**_NOTE:_** This application may contain custom code that is marked by the comments // START OF CUSTOM CODE ... and // END OF CUSTOM CODE. When using the MPLAB Harmony Configurator to regenerate the application code, use the "ALL" merging strategy and do not remove or replace the custom code.

Configuring the Hardware

This section describes how to configure the supported hardware.

Configure the hardware as follows:

Attach the 24-bit pass through card to the GFX Connector on the SAM E54 Curiosity Ultra board.
Connect the ribbon cable from the maXTouch Curiosity Pro Display to the ribbon connector on the 24-bit pass through card. Make sure that the S1 switch on the 24-bit pass through card is set to 2.
On the backside of the maXTouch Curiosity Pro display, set the IM[2:0] switches to 011 for 8-bit MCU mode.
Connect a USB cable from the host computer to the DEBUG USB port on the SAM E54 Curiosity Ultra board. This USB connection is used for code download and debugging.
Connect 5.5V power supply to the SAM E54 Curiosity Ultra board is optional

The final hardware setup should be:

Power up the board by connecting the power adapter to power connector or a powered USB cable to the DEBUG USB port on the board.

Running the Demonstration

The application first boots to an animated Splash Screen. Once the Splash Screen animation completes, the application boots to a Main Screen.

When at rest, the demo will cycle through idle sprite animations. Various areas of the screen are touch interactive

If initiated to run, the lamb sprite will run to the end of the screen, and play out a sequence of smacking into a wall, hurt and dizzy animations.

Tap Jump and the lamb will play out a jump animation.

Info Screen describes the features supported by this demo